Glenn Gonzalez
126-05 101 Avenue, #2
Richmondhill, NY 11419
347-993-8085
May 14th, 2009
Dear Hiring Manager:
Are you looking for a Certified & Experienced Electrician’s Helper/Jr. Mechanic with:
• 17 Months of hands-on experience in Commercial & Residential Electric work?
• Knowledge of the NEC Code, latest tools in the Electrical field?
• Excellent written and oral communication skills?
• A disciplined & efficient approach to every job?
• A passion to learn and to increase his skills?
If so, then you need look no further. You will see from my enclosed resume that I meet all of these qualifications and more.
I would very much like to discuss opportunities with your company. To schedule an interview, please call me at 347-993-8085. The best time to reach me is between 8AM and 10PM, but you can leave a voice message at any time, and I will return your call.
Please note if you are not hiring at this time I would appreciate you retaining my information on file for future consideration.
Thank you for taking the time to review my resume. I look forward to speaking with you.
Sincerely,
Glenn Gonzalez
Enclosures
GLENN GONZALEZ 126-05 101ST AVE, #2
(347)993-8085 Richmond Hill, New York 11419
ELECTRICIAN’S HELPER/JR MECHANIC
17 Months experience in the electrical field.
Class B Commercial Drivers License – NP Endorsements
Fluent in Spanish
RELEVANT EXPERIENCE AND ACCOMPLISHMENTS
Certificate 300 hours training program
Course Covered:
 Introduction Trade Electricity 1&2 Knowledge of basic tools and their uses, conductors, conduits and cables are among some of the topics covered. Ohm’s Law and Kirchhoff’s Law. Branch circuit calculations to find Ampacity, Voltage drop, box & conduit fills, and circuit load in (va) etc.
 Drawing of circuit schematics & cable layouts. Installation of device/junction boxes, receptacles and switches.
 Wiring & servicing of 1 & 2 family dwellings.
 Calculation of General Lighting and large equipment load to determine the minimum number of branch circuits and size of feeder and grounding conductors by utilizing the square footage of the dwelling.
 Wiring and servicing of commercial buildings.
 Calculation of general lighting and large equipment load to determine the type of service of feeder and grounding conductor by the square footage of the building.
 Motor and motor wiring.
 Conduit bending with the hand bender and hickey
 Geometry required in making proper bends.
 Making bends of specific angles.
 Making offsets and parallel offsets
 Calculating parallel offsets
 Troubleshooting circuits. Utilizing the multi-meter and pig tail method
 Voice data & telephone cabling
 Techniques of the trade
Experience
. Sept 2007 – Nov 2008 Mid- County Mechanical S. Richmond Hill, NY
Jr. Mechanic- Replaced and mounted panels 200A - 600A and Disconnect Switches. Worked on single ph and 3 ph panels. Installed infrared sensors, exhaust fans, 2ft- 8ft fixtures and replaced ballasts. Assisted in installing new 600A services from 200A. Bended EMT and rigid conduit, offsets - 90’s- 45’s, back to back bends, and saddles, using ½â€, ¾†& 1†benders and Hydraulic Bender for larger conduits. Ran Bx and EMT for lighting circuits, installed heaters and commercial A/C, also ran copper tubing for the units. Assisted in mounting air ducts and power washing A/C units. Replaced single phase and three phase motors, ran wire from 18 Gauge to 500 MCM, installed thermostats and wire, cleaned coils, pumped out basements. Assisted Electricians in the installation and repair of electrical wiring, fixtures, and equipment.
Performed any combination of the following tasks:
 Gathered tools and supplies to be used at work site, according to instructions. Measured, cut and bent wire and conduit, using ruler and hand tools. Drilled holes for wiring, using power drill, and pulled or pushed wiring through openings by hand or with Wire Puller.
Traced out short circuits in wiring, using knowledge of wiring and test meter.
Assisted in lifting, positioning, and fastening objects, such as wiring and conduit.
 Performed minor repairs, such as replacing fuses, light sockets, bulbs, and switches, using hand tools. Maintained tools and equipment and kept supplies and parts in order. Disassembled defective electrical equipment, replaced defective or worn parts, and reassembled equipment, using hand tools.
 Conducted skilled journey-level electrical work involving installations, modifications, inspections, troubleshooting, and repairs to industrial-type electrical systems
 Assisted mechanic in cutting, bending and in the assembly and installation of electrical conduit.
 Pulled wires through raceways and conduits, mounting outlets and switches
 Assisted mechanics in troubleshooting alarm systems, lighting systems, etc.
 Threaded conduit ends, connected couplings, fabricated and secured conduit support brackets
 Maintained inventory in work Van and maintained cleanliness of work Van
CAREER HISTORY
January 2002 - January 2003
Ozone Park Lumber S. Ozone Park, NY Commercial Driver – Class B with NP Endorsements
Delivered lumber, sheetrock and other materials used in construction in the tri-state area.
1999 -2000
Meyerson Associates New York, NY
Security Supervisor – Responsible for a team of 8 security guards who covered buildings in NYC, checking boiler rooms and investigating tenant complaints
Private investigation work involving insurance claims and reporting findings
Body Guard Services provided at events i.e. charity events and fashion shows
1990-1995
US Army
Light Wheel vehicle mechanic – Servicing, repairing and trouble shooting army vehicles such as Hummvees deuce and ½ and quarter ton vehicles.
Ranger – Airborne, Airassault, Squad Leader in charge of 10 soldiers
REFERENCES
Available upon Request
NukeJobs is a nuclear jobs board that provides nuclear job seekers access to international directories of Nuclear Employers, Nuclear Resumes and Nuclear Jobs such as Nuclear Engineer Jobs, Nuclear Construction Jobs, Nuclear Power Plant Jobs, Nuclear Medicine Jobs, Nuclear Pharmacy Jobs, Nuclear Security Jobs, Nuclear Physics Jobs, Nuclear Reactor Jobs, Nuclear Material Jobs, Nuclear Safety Jobs, and Nuclear Waste Jobs.