I would like to find a good company to stay and grow with. I work very hard, willing to work any hours asked of me. I do not mind if a relocation is required or travel. I have my own truck and tools.
230 Mercury Drive 256-342-7379
Arab Alabama. 35016 Lexas50[at]yahoo.com
Ronaldo Cunningham
Objective: I have good job ethics, to do a job to my greatest ability in a safe manner. Completing a project from start to finish correctly. I aim to gain employment where my skills as an electrician can be utilized to their greatest potential.
Accomplishments: Tested voltage, resistance, and phase angle in circuits. Using voltmeters, ohm meters, and phase rotation indicators. Prepared and maintained all equipment used in safety and compliance testing, and passed all equipment tests successfully.
Education: High School Diploma 1996 Ayers Technical Collage, Anniston Alabama.
I am also currently in school with DeVry University getting my electrical engineering bachelors degree.
Certificates:
2006 US Department of Labor Mine Safety and Health Administration, Birmingham Alabama.
Completed course work in mines, which has significantly contributed to my expertise in Electrical field.
I have completed a ten hour course in OSHA.
I have been trained and certified in scissor lifts and boom lifts.
I have been trained and certified in Hilti powder actuated tools.
Skills:
I can operate hydraulic benders, hand benders and Chicago benders.
I can operate scissor lifts, JLG lifts or boom lifts and fork lifts.
I can operate pipe threaders and hoghead threaders.
I can read blueprints.
Experience :
Zachary Inc. Alexander City, Alabama Jan. 2009- Feb. 2009
I was on temporary power, provided power for welding machines, stress machines. I ran rigid conduit and worked with GE for support.
Meg wires, hi- pot wires, checked high voltage breakers. Also worked on the grounding for motors, skids, and turbine generator.
Becon - Bedford Kentucky. Nov. 2008- Jan. 2009
I worked on wire pulling crew and ran aluminum conduit from three quarter to an inch and a half.
Zachary Inc. Loxohatchee, Florida. July-2008-Oct. 2008
I was on temporary power, I sat up 277/480 power panels to provide power for welding machines, stress machines and normal power.
I installed Clodic Protection, and ran rigid conduit for it.
C.E.S. for Moody Electric. Pascagoula Mississippi May 2008- June 2008
Chevron oil refinery shutdown.
I worked on temp. power, provided lighting, hooked up welding machines and stress machines.
Acker Electric through C.E.S. Coldwater, Alabama. 2007-2008
I helped pull 15 kva, 650, 500, 350...etc.
Terminated plc, rpc, lighting contact panels, checked phase, terminated disconnects and transformers. Installed conduit from 5†to ¾†rigid and e.m.t , worked on grounding and bonding equipment, and worked on fire alarm systems.
T.I.C. St. Petersburg Florida 2007-2007
I ran five inch PVC for duck banks, installed intermedia for pvc, and tied down pvc.
I was cleared for homeland security.
ETS Birmingham Alabama 2007-2007
I installed two inch to three quarter pipes, pulled wire, terminated motors, starters and lighting panels.
Stone and Sons through C.E.S Ragland/Clera Alabama 2006-2007
I terminated control panels, disconnects, limit switches, sensors, transformers, MCC’s stop and start buttons, valve controls, and motors. I also installed rigid and EMT pipe from two inch to three quarter.
OCI, Lakeland Florida 2005-2006
I terminated control panels, PLC’s, JB’s, motors, stop and start buttons, limit switches, disconnects, MCC’s, phoned out cable wires to make sure they were at the right location, used megger for locating damaged wires, terminated switch gears. I also wired up some Mach 5.
Tested voltage, resistance and phase angle in circuits, used volt meter, ohm meter, and phase rotation indicators.
I prepared and maintained all equipment used in safety and compliance testing.
CES, Marrietta Georgia 2004-2005
I ran one inch to three quarter rigid pipe for conveyer belts.
Terminated limit switches, audio and visual camera systems and control panels. Installed cable trays and installed eathernet cable for motor controls.
Tradesmen International, West Palm Beach Florida, 2002-2004
I pulled 650, #2 wire for high rise building, installed rigid pipe from two inch to three quarter, made up power panels, and troubleshoot lighting and plugs.
Also I did commercial and industrial work for Tradesmen International. Adjusted, repaired, and replaced defective wiring and relays in ignition lighting, air-conditioning, and safety control systems using electrician’s tools.
P&S Heating and air Heflin Alabama, 2002-2002
I replaced worn and defective parts, such as switches, bearings, transmissions, belts, gears, circuit boards, and defective wiring.
I connected appliance to power source and used test instruments to calibrate timers and thermostats and adjust contact points.
Terry Hogge Electric, Talladega Alabama 2002-2002
I installed wiring, fixtures and equipments for all electrical services in residential construction projects, following blueprints and wiring diagram. Installed exterior conduit and threaded wires through conduits to terminals, including connection boxes, circuit breakers, voltage regulators, and switch panels.
Terminated disconnects, LP’s, RP’s limit switches and relays.
References:
Chris Sappington - Master Electrician
(931) 510-5809
I have known him for 5 years.
Robin Seasock- Journeyman Electrician
(352) 542-9449
I have known him for 2 years.
Gary Gilbert- Journeyman Electrician
(615) 429-6995
I have known him for 7 years.
John Hall - Journeyman Electrician
(614) 202-4209
I have known him for 3 years.
Chad Dulin- Journeyman Electrician
(256) 831-9627
I have known him for 15 years.
Tim Osbourne- Journeyman Electrician
(937) 830-7088
I have known him for 2 years.
Richard Green- Journeyman Electrician
(919) 288-8840
I have known him for 3 years.
NukeJobs is a nuclear jobs board that provides nuclear job seekers access to international directories of Nuclear Employers, Nuclear Resumes and Nuclear Jobs such as Nuclear Engineer Jobs, Nuclear Construction Jobs, Nuclear Power Plant Jobs, Nuclear Medicine Jobs, Nuclear Pharmacy Jobs, Nuclear Security Jobs, Nuclear Physics Jobs, Nuclear Reactor Jobs, Nuclear Material Jobs, Nuclear Safety Jobs, and Nuclear Waste Jobs.